Allegro MicroSystems, LLC
Bild kan vara representation.
Se specifikationer för produktinformation.
ACS756KCB-050B-PFF-T
Visa detalj Datablad

ACS756KCB-050B-PFF-T

Introduction

The ACS756KCB-050B-PFF-T is a current sensor belonging to the category of integrated circuits. It is commonly used for measuring current in various electronic applications. This sensor possesses unique characteristics and packaging, making it suitable for a wide range of use cases.

Basic Information Overview

  • Category: Integrated Circuit
  • Use: Current sensing in electronic applications
  • Characteristics: High accuracy, low noise, small form factor
  • Package: Surface mount package
  • Essence: Accurate current measurement
  • Packaging/Quantity: Available in tape and reel packaging, quantity varies by supplier

Specifications

  • Operating Voltage: 3V to 5.5V
  • Sensitivity: 40mV/A
  • Bandwidth: DC to 120kHz
  • Output: Analog voltage output proportional to the sensed current
  • Temperature Range: -40°C to 125°C
  • Isolation Voltage: 2.1kV RMS

Detailed Pin Configuration

The ACS756KCB-050B-PFF-T features a 5-pin configuration: 1. VCC (Power supply) 2. GND (Ground) 3. VIOUT (Analog voltage output) 4. NC (No connection) 5. NC (No connection)

Functional Features

  • High accuracy current sensing
  • Low noise output
  • Wide operating temperature range
  • Small form factor for space-constrained applications

Advantages and Disadvantages

Advantages

  • Accurate current measurement
  • Wide operating temperature range
  • Low noise output

Disadvantages

  • Limited isolation voltage compared to some alternatives
  • Higher cost compared to basic current sensors

Working Principles

The ACS756KCB-050B-PFF-T operates based on the principle of Hall effect sensing. When a current flows through the sensor, it generates a magnetic field that is sensed by the integrated Hall-effect sensor, producing an analog voltage output proportional to the sensed current.

Detailed Application Field Plans

This sensor is widely used in various applications, including: - Motor control systems - Power management systems - Battery monitoring - Overcurrent protection circuits - Industrial automation

Detailed and Complete Alternative Models

Some alternative models to the ACS756KCB-050B-PFF-T include: - ACS712 - ACS770 - INA219 - MAX4376

In conclusion, the ACS756KCB-050B-PFF-T is a versatile current sensor with high accuracy and a wide range of applications. Its compact size and precise measurements make it a popular choice for electronic systems requiring current sensing capabilities.

[Word Count: 345]

Lista 10 Vanliga frågor och svar relaterade till tillämpningen av ACS756KCB-050B-PFF-T i tekniska lösningar

  1. What is the ACS756KCB-050B-PFF-T?

    • The ACS756KCB-050B-PFF-T is a fully integrated Hall-effect-based linear current sensor IC with 2.5 kV isolation and a low resistance current conductor.

  2. What is the maximum current it can measure?

    • It can measure DC or AC currents up to ±50A, making it suitable for a wide range of applications.

  3. How does the ACS756KCB-050B-PFF-T provide electrical isolation?

    • The device incorporates an isolation voltage rating of 2.5 kV, ensuring safe and reliable operation in high voltage systems.

  4. What are the typical applications for the ACS756KCB-050B-PFF-T?

    • Typical applications include motor control, load detection and management, power supplies, and overcurrent fault protection.

  5. What is the output signal of the ACS756KCB-050B-PFF-T?

    • The device provides an analog output voltage proportional to the AC or DC currents being measured.

  6. How accurate is the ACS756KCB-050B-PFF-T?

    • It offers high accuracy with low offset and gain errors, making it suitable for precision measurement applications.

  7. What is the operating temperature range of the ACS756KCB-050B-PFF-T?

    • The device operates reliably over a wide temperature range, typically from -40°C to 125°C.

  8. Does the ACS756KCB-050B-PFF-T require external calibration?

    • No, the device is factory calibrated to provide accurate measurements without the need for user calibration.

  9. Can the ACS756KCB-050B-PFF-T be used in automotive applications?

    • Yes, it is AEC-Q100 qualified, making it suitable for automotive systems such as battery management and motor control.

  10. Is the ACS756KCB-050B-PFF-T available in different package options?

    • Yes, it is available in a lead (Pb) free, small footprint surface mount package for ease of integration into various designs.